Foliar Diseases and Fungicide Applications in Corn

Author:  Comments Off on Foliar Diseases and Fungicide Applications in Corn

Trying to decide whether or not to spray fungicide on your corn? First, you should scout for diseases and consider your disease risk. Southern rust has been reported in TX, MS, AL, AR, GA, and FL and with the tropical storm there is a good chance spores have been blown in to TN and the wet, overcast weather provides the perfect environment for disease development.

Deciding to apply a fungicide to corn should be based upon multiple factors including:

  • Disease presence
  • Weather conditions
  • Cropping history
  • Hybrid disease susceptibility

Foliar fungicide applications in corn is more likely to provide a response in yield when disease is present or there is significant risk of disease, weather conditions favor disease development, the field is corn after corn, and a disease susceptible hybrid is planted.  Research data from University of Tennessee and other universities has continuously found these factors to strongly influence the magnitude and consistency of yield response to a foliar fungicide application in corn.

When factors warrant a fungicide application, the application timing that has provided the most consistent yield response over non-treated corn is a fungicide application at VT or R1 growth stages (tasseling to pollination).

Major corn diseases are favored by humid conditions, so the edges of fields will not be the place to scout.  Within fields, especially low spots that hold moisture are good areas to scout for disease as it may develop in those areas first. Be on the lookout for lesions and use the resources on and particularly under Corn Diseases in the photo gallery (Corn Diseases in Tennessee) which contains disease images and weather conditions that favor disease development. For you tweeters out there, tweet a picture of any corn diseases you’re seeing, the disease name, and county and state to @corndisease.

Image 1. Beginning lesions of GLS in lower canopy
Image 2. Lesions of GLS elongating on corn leaf

One of the most common foliar corn diseases in Tennessee is gray leaf spot (caused by a fungus – Cercospora zea-maydis), especially in continuous corn fields (see Images 1 and 2).  Other diseases that may be seen include anthracnose leaf blight (caused by a fungus – Colletotrichum graminicola), Northern corn leaf blight (caused by a fungus – Exserohilum turcicum), Southern corn rust (caused by a fungus – Puccinia polysora), and common corn rust (caused by a fungus – Puccinia sorghi).

While southern corn rust is the one of the most damaging diseases, be sure it is correctly identified and not confused with common rust. The characteristics that differ between the rusts are the location, color, shape, and distribution of pustules (see table and images 3 and 4). When in doubt don’t hesitate to contact your local county agent for advice on disease management and identification.

Table 1. Comparison of Southern and Common Rust

 Pustule Characteristics:  Common Rust  Southern Rust
 Location  upper and lower leaf surfaces  primarily upper leaf surface
 Color  brownish, red  orange to light brown
 Shape  elongated  round
 Distribution  scattered  densely packed
 Other differences:
 Optimal Temperature  61-77 °F  77-82 °F
 Probability of Effecting  Yield  low  moderate
Image 3. Southern rust on upper side of corn leaf


Image 4. Common rust on corn










Data from the 2014 Regional Corn Fungicide Summary data generated by the Corn Disease Working Group (CDWG), compiled by Dr. Kiersten Wise from Purdue University, illustrates how yield response is highly influenced by the amount of disease. Fungicide applications at VT-R2 which had less than 5% disease (86 observations) had a mean yield response of 3.0 bu/a compared to non-treated, while applications applied where there was more than 5% disease (121 observations) had a mean yield response of 11.1 bu/a.

Break even scenarios for corn fungicide application



The response in yield to break-even on fungicide application can be found in the table below.  Using a wide net of break-even scenarios based on past average corn prices and $12 to $36 application costs the table shows bushels per acre response that would be required to recover the cost of the fungicide application.




There are multiple fungicides labeled for corn and for the control of different diseases. The multistate collaborative, the Corn Disease Working Group (CDWG), has developed information on fungicide efficacy for control of certain corn diseases. This corn fungicide efficacy table can be found at (Corn Fungicide Table – CDWG) and linked here as well.  Application coverage is also important, which includes using sufficient amount of water per acre and adequate droplet size based on the product being applied.

Print Friendly, PDF & Email